D-Series [ja]

Specification

Product type	Produkttyp	Product type	产品类型	Product type									DPE-10-500	DPE-30-500	DEN-10-500	DEH-30-500	DAN-10-150	DAN-30-150	DAE-10-050	DBN-50-050
Part No.	Artikel-Nr.	Part No.	订货号	Part No.	500630	500636	500637	500638	500632	500634	500633	500635	500630	500636	500637	500638	500632	500634	500633	500635
Specifications	Spezifikation	Specifications	规格	Specifications
Measuring range on reflective foil	Messbereich auf Reflexionsfolie	Measuring range on reflective foil	反射板量程	Measuring range on reflective foil	~0.5...500 m	~0.5...500 m	~0.5...500 m	~0.5...500 m	~40...150 m	~40...150 m	~40...50 m	-	~0.5...500 m				~40...150 m		~40...50 m	-
Measuring range on natural surfaces	Messbereich auf natürliche Oberflächen	Measuring range on natural surfaces	自然表面量程	Measuring range on natural surfaces	0.05...~100 m	0.05...~100 m	0.05...~100 m	0.05...~100 m	0.05...~100 m	0.05...~100 m	0.05...~50 m	0.05...~50 m	0.05...~100 m						0.05...~50 m
Typical accuracy @ 2σ	Typische Genauigkeit @ 2σ	Typical accuracy @ 2σ	典型精度 @ 2s	Typical accuracy @ 2σ	± 1 mm	± 3 mm	± 1 mm	± 3 mm	± 1 mm	± 3 mm	± 1 mm	± 5 mm	± 1 mm	± 3 mm	± 1 mm	± 3 mm	± 1 mm	± 3 mm	± 1 mm	± 5 mm
Repeatability typ.	Typische Wiederholungsgenauigkeit	Repeatability typ.	重复精度 @ 2s	Repeatability typ.	± 0.3 mm	± 0.7 mm	± 0.3 mm	± 0.7 mm	± 0.3 mm	± 0.7 mm	± 0.3 mm	± 1.8 mm	± 0.3 mm	± 0.7 mm	± 0.3 mm	± 0.7 mm	± 0.3 mm	± 0.7 mm	± 0.3 mm	± 1.8 mm
Max measuring rate	Max. Messrate	Max measuring rate	最大测量频率	Max measuring rate	250 Hz	250 Hz	100 Hz	100 Hz	100 Hz	100 Hz	100 Hz	10 Hz	250 Hz		100 Hz					10 Hz
Operating temperature	Betriebstemperatur	Operating temperature	工作温度范围	Operating temperature	-40...+60 °C	-40...+60 °C	-10...+50 °C	-10...+60 °C	-10...+50 °C	-10...+50 °C	-40...+60 °C	-10...+50 °C	-40...+60 °C		-10...+50 °C	-10...+60 °C	-10...+50 °C		-40...+60 °C	-10...+50 °C
Degree of Protection	Schutzart	Housing	防护等级	Degree of Protection	IP65	IP65	IP65	IP65	IP65	IP65	IP65	IP65	IP65
Power supply	Versorgungsspannung	Power supply	工作电压范围	Power supply	12...30 VDC	12...30 VDC	12...30 VDC	12...30 VDC	12...30 VDC	12...30 VDC	12...30 VDC	12...30 VDC	12...30 VDC
Laser red, visible	Laser rot, sichtbar	Laser red, visible	激光，红色可见光	Laser red, visible
Diameter laser dot at 10m	Durchmesser Laserpunkt bei 10m	Diameter laser dot at 10m	激光光斑大小@10 m	Diameter laser dot at 10m	7x3 mm	7x3 mm	7x3 mm	7x3 mm	7x3 mm	7x3 mm	7x3 mm	7x3 mm	7x3 mm
Diameter laser dot at 50m	Durchmesser Laserpunkt bei 50m	Diameter laser dot at 50m	激光光斑大小@ 50 m	Diameter laser dot at 50m	28x13 mm	28x13 mm	28x13 mm	28x13 mm	28x13 mm	28x13 mm	28x13 mm	28x13 mm	28x13 mm
Diameter laser dot at 100m	Durchmesser Laserpunkt bei 100m	Diameter laser dot at 100m	激光光斑大小@100m	Diameter laser dot at 100m	55x30 mm	55x30 mm	55x30 mm	55x30 mm	55x30 mm	55x30 mm	55x30 mm	55x30 mm	55x30 mm
Dimensions (l x w x h)	Abmessungen (l x b x h)	Dimensions (l x w x h)	尺寸(L × W × H)	Dimensions (l x w x h)	140x78x48 mm	140x78x48 mm	140x78x48 mm	140x78x48 mm	140x78x48 mm	140x78x48 mm	140x78x48 mm	140x78x48 mm	140x78x48 mm
Weight	Gewicht	Weight	重量	Weight	350 g	350 g	350 g	350 g	350 g	350 g	350 g	350 g	350 g
Interfaces	Schnittstellen	Interfaces	接口	Interfaces
Analog output, programmable, 0/4...20 mA	Analogausgang, programmierbar, 0/4...20 mA	Analog output, programmable, 0/4...20 mA	模拟量输出，可编程, 0/4...20 mA	Analog output, programmable, 0/4...20 mA
Max error analog output	Max. Fehler des Analaogausganges	Max error analog output	模拟量精度	Max error analog output	± 0.1 %	± 0.1 %	± 0.1 %		± 0.1 %	± 0.1 %	± 0.1 %	± 0.2 %	± 0.1 %				± 0.1 %			± 0.2 %
2 digital outputs, programmable	2 digitale Ausgänge, programmierbar	2 digital outputs, programmable	2 数字量输出，可编程	2 digital outputs, programmable
1 digital output, error display	1 digitaler Ausgang für die Fehleranzeige	1 digital output, error display	1 数字量输出，可编程/错误显示	1 digital output, error display
1 digital input, programmable (instead of DO1)	1 digitaler Eingang, programmierbar (anstelle DO1)	1 digital input, programmable (instead of DO1)	1 数字输入类型，可编程 (而不是 DO1)	1 digital input, programmable (instead of DO1)
RS-232	RS-232	RS-232	RS-232	RS-232
RS-422 with programmable ID	RS-422 mit programmierbarer ID	RS-422 with programmable ID	RS-422 可编程 ID	RS-422 with programmable ID
SSI	SSI	SSI	SSI	SSI
PROFINET (option)	PROFINET (option)	PROFINET (option)	PROFINET (选购)	PROFINET (option)
EtherNetIP (option)	EtherNetIP (option)	EtherNetIP (option)	EtherNetIP (选购)	EtherNetIP (option)
EtherCAT (option)	EtherCAT (option)	EtherCAT (option)	EtherCAT (选购)	EtherCAT (option)
PROFIBUS (extern)	PROFIBUS (extern)	PROFIBUS (extern)	PROFIBUS (外设)	PROFIBUS (extern)
Connection	Anschlussart	Connection	连接方式	Connection
Internal screw terminal	Interne Anschlussklemmen	Internal screw terminal	接线端子	Internal screw terminal
Features	Funktionen	Features	特点	Features
Auto start	Auto Start	Auto start	自动模式下独立工作	Auto start
Direct connectivity of an external remote display	Direktes Anschliessen einer externen Anzeige	Direct connectivity of an external remote display	直接连接外部显示器	Direct connectivity of an external remote display
External trigger for measurements	Externe Auslösung von Messungen	External trigger for measurements	触发功能	External trigger for measurements

Application
AE0104 Floodgate position measurement [ja]
Dimetix laser distance sensors are used to monitor floodgates. This means that the amount of water outflow is known at all times. The sensors measure the exact position of the floodgates in millimeter-precision and absolutely contactless.
- D-Series [ja]
AE0112 Cutting application [ja]
In the metal industry, devices for length division are frequently used. However, many standard solutions, presently available on the market, are not optimal for some companies. With Dimetix laser distance sensors, an inexpensive special model is offered.
- D-Series [ja]
AE0202 Monitoring of pressure tunnel [ja]
An automatic monitoring system is used in a headwater pressure tunnel to measure the passive bias of penstocks during injections. As soon as the limit values were exceeded, an alarm lamp is illuminated, so that the injections can be stopped.
- D-Series [ja]
AE0203 Supervision of railway infrastructure [ja]
Accurate distance measurement is essential in railway construction – for new development as well for maintenance. Speed trains of the latest generation move at maximum speeds of over 300km/h, in order to preserve the rolling stock at such strains, millimeter precise measuring is inevitable.
- D-Series [ja]
AE0205 Monitoring of rockformation above railwaytrack [ja]
Dimetix sensors are used to monitor a debris flow activity. These rocks can lead to the accumulation of a mountain stream, which can lead to a flooding of a rail track. In addition, two additional lasers are used to monitor a large boulder that moves downhill and warns communities in danger.
- D-Series [ja]
AE0207 Movement of large structures [ja]
In order to move large structures as bridges and buildings, the PolyDist system is the optimal solution. With up to four Dimetix sensors the process of moving is constantly monitored so that the structure can be moved and repositioned precisely.
- D-Series [ja]
AE0209 Monitoring of railway tunnel [ja]
During construction work on railway infrastructure automated monitoring systems are crucial to early detect potentially hazardous structural deformations. As Ristag AG successfully demonstrated with this tunnel monitoring system, expensive standard surveying equipment can often be substituted by much more economical Dimetix laser distance sensors, while maintaining the demanded monitoring accuracy and reliability.
- D-Series [ja]
AE0305 Monitoring of heritage materials [ja]
In historic buildings the fabric can often become damaged. With the aid of a measuring concept, which includes Dimetix sensors, the evolution of historical buildings are monitored and examined.
- D-Series [ja]
AE0401 Truck position measurement [ja]
In times of increasing traffic and ever more demanding tasks where time is of the essence, a system has been developed to speed up customs inspections on HGV vehicles. This device significantly helps to reduce time consumption checking up on vehicles as the positioning of trucks can be done with sensors. Customs uses mobile X-Ray scanners to examine the content of trucks and containers. During the scanning process, movements of the scanner must be precisely determined.
- D-Series [ja]
AE0502 Glass panel measurement [ja]
In order to transport glass panels, they are positioned after production from a conveyor belt onto a pallet. To prevent glass breakage, a system of DIMETIX sensors has been developed to precisely monitor positioning.
- D-Series [ja]
AE0503 Silo level measurements [ja]
With Dimetix laser distance sensors, the level in silos can be exactly measured at any time. The Dimetix sensors measure on different surfaces, like stones, sand, grain or dark surfaces.
- D-Series [ja]
AE0505 Automated diameter & width measurement [ja]
An exact measurement is extremely important when positioning and dimensioning paper rolls. The Dimetix laser distance sensors measure the width of the paper roll using two sensors on each side of the paper roll.
- D-Series [ja]
AE0506 Monitoring transfer car position [ja]
In a steel production facility, large transfer cars transport glowing steel plates. Due to a malfunction of the micro-switches, cars collided at the end of a transfer line. With the help of two Dimetix lasers integrated in protective housings, smooth operation could be restored.
- D-Series [ja]
AE0507 Saw blade alignment [ja]
Large saw blades used for cutting different materials frequently shift out of alignment, resulting in cuts at wrong angles, unnecessary reworking and wasted scrap. Our maintenance-free laser distance sensor saw blade alignment system provides a reliable, repeatable and cost-effective means of improving production quality and eliminating unnecessary scrap.
- D-Series [ja]
AE0508 Measuring flood gate height [ja]
The ability to reliably and precisely monitor flood gate height is a challenge for hydropower and reservoir flood gate operators. Dimetix laser sensors can be used for remote monitoring of the flood gates. The sensors measure the distances on the surface of the flood gates.
- D-Series [ja]
AE0509 Laser controlled cut-off solution [ja]
Increasing operational demands, a multiplicity of maintenance requirements and the growing importance for efficiency are crucial factors in nearly all industries. This is relevant for metal production and especially true for small and medium-sized companies at the heart of manufacturing and metalworking. Laser measurement technology provides an economical approach to reducing production delays and improving quality. Our affordable technological advantage helps you increase efficiency.
- D-Series [ja]
AE0510 Bridge structural monitoring [ja]
Dimetix made history in 2010 by collaborating with Applied Geomechanics, Inc., to develop a system to monitor the lift and placement of steel bridge truss sections on the Huey P. Long Bridge over the Mississippi River in New Orleans. The project involved transportation by river barge, the lifting and placement of the pre-assembled bridge truss spans to reduce stress on the bridge and minimize interruption of traffic. Ten DLS-C laser distance sensors were lifted aboard the 2,700 ton trusses and were used in conjunction with specially fabricated targets and software developed to monitor beam deflection during the day-long lift.
- D-Series [ja]
AE0511 Structural health monitoring [ja]
In modern urban environments, heavy construction often must be conducted immediately adjacent to properties and structures that must remain open to business or residency during excavation and construction. Traditional surveying techniques allow for +/-5 mm precision of displacement, but Dimetix laser distance sensor technology allows for measurements with sub-millimeter accuracy at distances up to 500 m to detect any shift or displacement of structures.
- D-Series [ja]
AE0601 Lifting of mining equipment [ja]
In mining applications, Dimetix laser distance sensors have been used to ensure accurate lifting and lowering processes of superstructures. In the case of a deviations, a signal was sent to the hydraulic system so that corrections can be made.
- D-Series [ja]
AE0701 Length positioning of wood binders [ja]
Spruce wood has been produced at our customer's facility for decades with great care and professional competence, as spruce wood is not a freely interchangeable material, the crucial difference is in countless details that have been perfected over the many years. Our customer has the most modern know-how for the production of cutting for a wide range of applications such as planking, timber construction, roof constructions, pallet production etc. Dimetix lasers are therefore used daily. Truss length measurement is used for positioning and to enhance their operational efficiency.
- D-Series [ja]
AE1102 Controlling of the filling and pour of steel and iron [ja]
Dimetix sensors were installed in foundries to monitor the moulding of hot steel and iron. With the aid of the sensors, fluid levels can be measured and an overflows avoided.
- D-Series [ja]
AE1601 Rock surveillance tsunami warning [ja]
In Norway, an early warning system was developed using three Dimetix sensors, which regularly measure the daily movement of rock above a bay. Thus, a warning can be triggered in the event of a potential landslide.
- D-Series [ja]
AN2001 Numeric digital display [ja]

This application note shows how to read a measured distance value from a standard external numeric digital display. Descriptions of the wiring and sensor configuration are included and two samples are shown.
- D-Series [ja]
AN2002 SSI interface usage [ja]

SSI is a widely used serial interface standard for industrial applications between a master (for example, controller) and a slave (for example, a Laser Distnace Sensor). On an SSI communication channel, the master generates a clock, while the slave sends the data corresponding to the clock signal received. Only point-to-point communication is possible with the SSI interface. The RS-422 standard defines the electrical signal levels of the SSI interface.
- D-Series [ja]
AN2003 RS-422 connection to RS-485 [ja]
This document explains how to connect the RS-422 interface of the Laser Distnace Sensor to a RS485 double-wire interface. This application note requires special skils, therefore a request for this adaptation must be made by e-mail to Dimetix.
- D-Series [ja]
AN2004 EXCEL Example [ja]
This application note describes how to control a Dimetix distance sensor connected to a serial interface by VBA (Visual Basic for Application). The VBA program is integrated into an EXCEL worksheet.
- D-Series [ja]
AN2006 Timed measurement characteristic example [ja]
The Laser Distance Sensor offers configuration possibilities for fixed time measurements. This application note gives some configuration examples and describes the specialities of the timed measurement characteristics.
- D-Series [ja]
AN2007 Additional measurement filter – distance jump [ja]
The D-Series Laser Distance Sensors provide a wide range of configuration possibilities. This document shows how to configure the distance jump detection feature. This feature works like a plausibility check of the measured distance. In typical use, cases offer positioning applications (for example, in logistics).
- D-Series [ja]
AN2010 S7 connection to RS422 [ja]
This application note describes how to connect a Laser Distance Sensor to a CP340 interface of a Siemens S7 PLC. Configuration and wiring are described. In addition to this application note an example for the S7 is also included on our website.
- D-Series [ja]
AN2011 Moving Target Characteristic [ja]
Many position control tasks require fast and precise distance measurement with a constant output rate. Especially for these requirements the Dimetix laser distance sensors provide the Moving Target measurement characteristics.
- D-Series [ja]
AN2018 Moving target characteristic with RS-422 [ja]
The moving target characteristic has been created for fast position measurement on continuously moving targets. This document describes the necessary settings of the laser distance sensor for the moving target characteristic as well as the configuration of the RS-422 interface.
- D-Series [ja]
AN2019 Moving target characteristic with SSI [ja]
The moving target characteristic has been made for fast position measurement on continuously moving targets. This document describes the necessary settings of the Laser Distance Sensor for the moving target characteristic as well as the configuration of the SSI and Analog interface.
- D-Series [ja]
AN2020 Positioning with SEW drives [ja]
This document describes how to use the FLS-C sensor in a positioning application in conjunction with a SEW servo drive. The necessary configuration of the FLS-C and the configuration of the SEW inverter are described . Further the wiring is also documented.
- D-Series [ja]
AN2040 Getting started with PROFINET [ja]
This is a simple example of how to get started with the PROFINET® interface of the Dimetix D-Series Laser Distance Sensors. All information and instructions necessary to understand this example of useage and to run this on a Siemens SIMATIC S7 PLC are included.
- D-Series [ja]
AN2041 Getting started with EtherNetIP [ja]
This is a simple example of how to get started with the EtherNet/IP™ interface of the Dimetix D-Series Laser Distance Sensors. All information and instructions necessary to understand this example of useage and to run this on an Allen Bradley CompactLogix PLC are included.
- D-Series [ja]
AN2042 Getting started with EtherCAT [ja]
This is a simple example of how to get started with the EtherCAT® interface of the Dimetix D-Series Laser Distance Sensors. All information and instructions necessary to understand this example of useage and to run this on a Beckhoff EtherCAT® master PLC are included.
- D-Series [ja]
Accessory
500308 Alignment Unit D-Series [ja]
Allows +/-4° adjustment in two axis; Ideal for distances up to about 300m; Steel, zinc-plated; Applicable for D-Series; country of origin: Switzerland
D-Series [ja]
500309 Protective Cover for Alignment Unit D-Series [ja]
For light, short-term outdoor applications; Protection only with horizontal laser exit; No IP protection class; Can only be used together with "500308 Alignment unit D-Series"; country of origin: Switzerland
D-Series [ja]
500700 PROFINET Interface for D-Series [ja]
An exchangeable cover for self installation; country of origin: Switzerland
D-Series [ja]
500701 EtherNet/IP Interface for D-Series [ja]
An exchangeable cover for self installation; country of origin: Switzerland
D-Series [ja]
500702 EtherCAT Interface for D-Series [ja]
An exchangeable cover for self-installation; country of origin: Switzerland
D-Series [ja]
500310 Air-cooling jacket for D-Series sensors with standard interface [ja]
This air-cooling jacket can be used with all Dimetix D-Series Laser Sensors that are equipped with standard interfaces. The sensor extensions PROFINET, Ethernet/IP and EtherCAT cannot be used with this air-cooling jacket.
D-Series [ja]
500311 Air-cooling jacket for D-Series Sensors with Industrial EtherNet [ja]
This air-cooling jacket protects the laser sensor and cools it with air. It is used with the Dimetix D-Series sensors that are equipped with the sensor extensions PROFINET, Ethernet/IP or EtherCAT. The Dimetix D-Series Laser Sensors that are equipped with standard interfaces require a different air-cooling jacket.
D-Series [ja]
500595 Accessories for Starter Kit D-Series [ja]
USB-cabel 2m Power supply USB-Stick with Manual, Utility Software and accessories summary country of origin: Switzerland
D-Series [ja]
500001 Calibration Certificate [ja]
for new measuring devices (must be ordered together with the device)
D-Series [ja]
500002 Recalibration Ceritficate [ja]
Recalibration with calibration certificate for used measuring devices
D-Series [ja]
500205 Sensor cable, A-Coded, 5pole, 5m, female [ja]
with M12 5pin sensor-connector IP65, other side open ends country of origin: Italy
D-Series [ja]
500113 Reflective Plate 210 x 297 mm [ja]
The reflective aluminum target plate provides a defined measuring target. It improves the reflected signal strength. This improved signal strength is used by the D-Series to measure long-distance ranges. Please check the device specification to ensure the applicable minimum distances.
D-Series [ja]
500206 Sensor cable, 2x D-Coded, 4pole, 5m, male [ja]
with M12 4pin male sensor-connectors IP65 on both sides, cable color: green, for Industrial Ethernet country of origin: Taiwan
D-Series [ja]
500207 Sensor cable, D-Coded-RJ45, 5m [ja]
with M12 4pin male sensor-connector to RJ45, cable color: green, for Industrial Ethernet country of origin: Taiwan
D-Series [ja]
500114 Reflective Foil 600 x 1200mm [ja]
The reflective foil provides a defined highly-reflecting measuring target. It improves the reflected signal strength. This improved signal strength is used by the D-Series to measure long-distance ranges. Please check the device specification to ensure the applicable minimum distances.
D-Series [ja]
Software
Downloads

01 Datasheets [ja]
500638 DEH-30-500 Datasheet
500637 DEN-10-500 Datasheet
500636 DPE-30-500 Datasheet
500635 DBN-50-050 Datasheet
500634 DAN-30-150 Datasheet
500633 DAE-10-050 Datasheet
500632 DAN-10-150 Datasheet
500630 DPE-10-500 Datasheet
Product Comparison D-Series

03 Manual current [ja]
テクニカルリファレンスマニュアル
 Manual D-Series
Quick Start Guide
Manual Industrial Ethernet PROFINET / EtherNet/IP / EtherCAT

04 Industrial Ethernet & Fieldbus Files [ja]
GSDML File PROFINET interface for D-Series
EDS File EtherNet/IP interface for D-Series
ESI File EtherCAT interface for D-Series

05 Movies [ja]
MB010 How to use the adjustment aid
MB020 How to perform a reset
MB030 How to install the Industrial Ethernet interface
MB040 What are the basics to start sensor configurations
MB050 How to load and save configuration files
MB060 How to measure through glass
MB070 How to clean laser sensor optics
MB080 How to configure the digital output hysteresis

06 Flyers [ja]
Flyer D-Series
Flyer D-Series
Flyer D-Series

07 3D-Files [ja]
500310 3D File Air-cooling jacket for standard interface
500303 3D File Air-cooling jacket for standard interface
500311 3D File Air cooling jacket for Industrial ethernet
500306 3D File Air cooling jacket for Industrial ethernet
3D-Files D-Series
3D-File RTE

D-Series [ja]

Highlights

Buy

AE0104 Floodgate position measurement [ja]

AE0112 Cutting application [ja]

AE0202 Monitoring of pressure tunnel [ja]

AE0203 Supervision of railway infrastructure [ja]

AE0205 Monitoring of rockformation above railwaytrack [ja]

AE0207 Movement of large structures [ja]

AE0209 Monitoring of railway tunnel [ja]

AE0305 Monitoring of heritage materials [ja]

AE0401 Truck position measurement [ja]

AE0502 Glass panel measurement [ja]

AE0503 Silo level measurements [ja]

AE0505 Automated diameter & width measurement [ja]

AE0506 Monitoring transfer car position [ja]

AE0507 Saw blade alignment [ja]

AE0508 Measuring flood gate height [ja]

AE0509 Laser controlled cut-off solution [ja]

AE0510 Bridge structural monitoring [ja]

AE0511 Structural health monitoring [ja]

AE0601 Lifting of mining equipment [ja]

AE0701 Length positioning of wood binders [ja]

AE1102 Controlling of the filling and pour of steel and iron [ja]

AE1601 Rock surveillance tsunami warning [ja]

AN2001 Numeric digital display [ja]

AN2002 SSI interface usage [ja]

AN2003 RS-422 connection to RS-485 [ja]

AN2004 EXCEL Example [ja]

AN2006 Timed measurement characteristic example [ja]

AN2007 Additional measurement filter – distance jump [ja]

AN2010 S7 connection to RS422 [ja]

AN2011 Moving Target Characteristic [ja]

AN2018 Moving target characteristic with RS-422 [ja]

AN2019 Moving target characteristic with SSI [ja]

AN2020 Positioning with SEW drives [ja]

AN2040 Getting started with PROFINET [ja]

AN2041 Getting started with EtherNetIP [ja]

AN2042 Getting started with EtherCAT [ja]

500308 Alignment Unit D-Series [ja]

500309 Protective Cover for Alignment Unit D-Series [ja]

500700 PROFINET Interface for D-Series [ja]

500701 EtherNet/IP Interface for D-Series [ja]

500702 EtherCAT Interface for D-Series [ja]

500310 Air-cooling jacket for D-Series sensors with standard interface [ja]

500311 Air-cooling jacket for D-Series Sensors with Industrial EtherNet [ja]

500595 Accessories for Starter Kit D-Series [ja]

500001 Calibration Certificate [ja]

500002 Recalibration Ceritficate [ja]

500205 Sensor cable, A-Coded, 5pole, 5m, female [ja]

500113 Reflective Plate 210 x 297 mm [ja]

500206 Sensor cable, 2x D-Coded, 4pole, 5m, male [ja]

500207 Sensor cable, D-Coded-RJ45, 5m [ja]

500114 Reflective Foil 600 x 1200mm [ja]

01 Datasheets [ja]

03 Manual current [ja]

04 Industrial Ethernet & Fieldbus Files [ja]

05 Movies [ja]

06 Flyers [ja]

07 3D-Files [ja]